#Pro xp 4 roof install
To install the aluminum roof, follow these steps:ģ. Peel the backing off the roof foam. The 4-Seat Light Pocket Aluminum Roof is part number 2883991-458. The 2-Seat Light Pocket Aluminum Roof is part number 2883961-458. Torque to 18 in-lbs (2 Nm).ġ2. Finish by inspecting the door for proper operation.Īluminum Roof Installation Tools Required Torque the fasteners to 35 in-lbs (4 Nm).ġ1. Reinstall the trim bracket with the two fasteners. Start by installing the top tabs into the door panel and then slide the bottom mounts over the tabs protruding from the door panel.ĩ. Next, install the four previously removed U-nuts into the mounting locations of the accessory closeoff panel.ġ0. Align the door panel with the door frame and install the 11 door panel fasteners. To install the door closeoff inserts, follow these steps:ģ. Using a T20 TORX® socket, remove and retain the two bracket fasteners and trim bracket from the door panel.Ĥ. Next, using a T40 TORX® socket, remove and retain the 11 outer door panel fasteners.ĥ. Then, remove the door panel and carefully set it aside.Ħ. Next, remove the three metal clamps securing the door trim to the door panel and carefully remove the trim from the panel.ħ. Remove and retain the four U-nuts on the door trim and discard the trim.Ĩ. Align the accessory closeoff panel with the door panel. Torque the fasteners to 89 in-lbs (10 Nm).ĥ. Starting inside the vehicle, maneuver the rear panel over the seats and align the side clamps to the ROPS.Ħ. Compress the seal to fit securely against the body panel, ensuring the mounting bracket is outside of the rear panel.ħ. Rotate the two side clamps downward to secure the rear panel to the vertical tubes.Ĩ. Then rotate the two top clamps upward to secure the panel to the upper horizontal tube.ĩ. Finish by securing the poly panel to the panel bracket with the included knob fastener.ĭoors Closeoff Insert Installation Tools Required To install the rear poly panel, follow these steps:ģ. Using a T40 TORX® socket, remove and retain the two body panel fasteners from between the seats.Ĥ. Install the rear panel bracket with the previously removed fasteners, making sure the vertical part of the bracket is facing rearward. Rear Poly Panel Installation Tools Required To install a windshield, follow these steps:ġ. Park the vehicle on a flat, level surface and shift the transmission into PARK.Ģ. Turn the ignition switch OFF and remove the key.ģ. Align the windshield onto the ROPS while supporting the bottom to prevent scratches to finished surfaces.Ĥ. Rotate the four clamps out over the ROPS to lock into place.ĥ. The vents can be opened or closed by rotating up or down.Ħ. To remove the windshield, rotate the clamps inward to release them from the ROPS.
#Pro xp 4 roof full
View the full line of available Polaris windshields for other options. The Hard Coat Poly Vented Full Windshield is part number 2883756. For your safety, perform all installation steps in the sequence shown and retain the instructions for future reference and parts ordering information.įor more information on tools, read the Tools and Fasteners Guide.
#Pro xp 4 roof pro
This video describes the installation process for a windshield (0:41), rear poly panel (1:24), door close-off inserts (2:40), aluminum roof (4:19) and the side mirrors (5:45) on a Polaris RZR Pro XP.Īlways wear safety glasses and nitrile gloves when installing accessories on your RZR.īefore installation of any accessories, read the instructions thoroughly and verify all parts and tools are accounted for.
0 kommentar(er)
